Lutron » HomeWorks » Wave Electronics Systems

LUTRON INTERNATIONAL SEETOUCH® KEYPAD FACEPLATE

admin — Fri, 23 Jun 2023 11:03:05 +0000

HomeWorks® QS international seeTouch® keypads from Lutron provide homeowners with a simple and elegant way to operate lights, shades or drapes, motorised screens, thermostats and many other devices with a choice of models and a selection of colour finishes.

The faceplates for Lutron’s International SeeTouch® Keypads provide design and function flexibility to suit any need with various options available.

The models available are 2 button, 3 button, 4 button, 5 button with raise and lower, 6 button with raise and lower, 7 button with raise and lower, 8 button with raise and lower and 10 button with raise and lower.

The colour finishes available are Antique Brass, Antique Bronze, Arctic White, Argentum, Bright Brass, Bright Chrome, Bright Nickel, Gold Plated, Mica, Satin Brass, Satin Chrome and Satin Nickle.

These keypad faceplates are tested to withstand 15kV of electrostatic discharge without damage or memory loss, in accordance with IEC 801-2 and conform to CE, C-tick, UL and cUL standards.

FEATURES

Available in a variety of colours and finishes to match perfectly the aesthetic of your space
Easy to use button
SeeTouch® keypads are available with two to ten buttons, allowing customisation of the number of functions
Lutron® wall plates snap on with no visible means of attachment
Green status LEDs
Backlit button and engraving makes the keypads readable any time of the day or night
Field changeable button or wall plate kits allow for easy customisation
Available in insert and non insert styles
All terminal block inputs are over voltage and mis wire protected against wire reversals and shorts

SPECIFICATIONS

Power	24 to 36V 30 mA
Typical Power Consumption	0.6W 1 Power Draw Unit (PDU) Test conditions: all backlights on medium intensity, two LEDs on (two presets active), keypad powered at 24V
Communications	Connects to QS wired device link on Homeworks® QS processor
ESD Protection	Tested to withstand 15 kV electrostatic discharge without damage or memory loss, in accordance with IEC 801-2
Power Failure	Power failure memory. Should power be interrupted, the keypad will return to its previous state when power is restored.
Models	Please select from: Models: 2 button, 3 button, 4 button, 5 button with raise and lower, 6 button with raise and lower, 7 button with raise and lower, 8 button with raise and lower and 10 button with raise and lower Colour finishes: Antique Brass Antique Bronze Arctic White Argentum Bright Brass Bright Chrome Bright Nickel Gold Plated Mica Satin Brass Satin Chrome Satin Nickle
Wiring	Control wire must be 1 pair 1.0 mm2 (18 AWG) SELV/PELV/NEC® Class 2for power and 1 pair 0.5 mm2 to 1.0 mm2 (22 AWG to 18 AWG) SELV/PELV/NEC® Class 2 twisted/shielded for data
ESD Protection	Tested to withstand 15 kV electrostatic discharge without damage or memory loss, in accordance with IEC 801-2
Environment	Ambient operating temperature: 0°C / 32°F to 40°C / 104°F 0% to 90% humidity, non condensing Indoor use only.
Dimensions	Height: 86mm / 3.39″ Width: 86mm / 3.39″ Depth 41mm / 1.61″
Regulatory Approvals	CE, C-tick, UL and cUL

The post LUTRON INTERNATIONAL SEETOUCH® KEYPAD FACEPLATE appeared first on Wave Electronics Systems.

LUTRON HWQS PALLADOM INTERNATIONAL 2 COLUMN KEYPAD, PRE ENGRAVED

admin — Fri, 23 Jun 2023 11:03:05 +0000

Lutron’s HWQS Palladiom International 2 Column Keypad LUT-PKP-2C elevates the user experience with sleek and intuitive design and allows the control of Lutron load control devices via a QS link. The keypad is pre engraved for extra convenience and is available in a variety of finishes.

Lutron’s HWQS Palladiom International 2 Column Keypad LUT-PKP-2C elevates the user experience with sleek and intuitive design and allows the control of Lutron load control devices via a QS link.

The keypad is pre engraved for extra convenience and is available in a variety of finishes..

The HomeWorks QS wired Palladiom keypad allows the user to control lights, shades or drapes, temperature and 3rd party equipment. The keypad is wired to a HomeWorks QS processor on the QS link. Buttons and faceplates are flush to each other and feature consistent material, creating a clean, minimalist look.

Status of active button press or scene is indicated through intensity of backlighting which is configurable through the HomeWorks QS software. Dynamic Backlighting Management (DBM) automatically adjusts backlight intensity based on ambient lighting conditions. It can also be programmed in the HomeWorks QS software to adjust intensity by time of day or button presses.

FEATURES

Large buttons are easy to use
Buttons with white, backlit engraving make it easy to find and operate the keypad in low light conditions
Button engraving is easy to read
Faceplate snaps on with no visible means of attachment. Surface mount for easy installation, no backbox required
Works within Quantum, myRoom Plus and myRoom Prime systems
Status of active button press or scene is indicated through intensity of backlighting
Dynamic Backlighting Management (DBM) automatically adjusts backlighting intensity based on ambient lighting conditions
Backlighting can also be programmed in Quantum and myRoom systems to adjust backlighting intensity
IP20 rated

SPECIFICATIONS

	LUT-PKP-2C HWQS Palladiom 2 Column International Keypad – Pre engraved
Power	24V to 36 V 30mA
Typical Power Consumption	0.7W Test conditions: All backlights on medium intensity, two LEDs on (two pre-sets active), keypad powered at 24V
Communications	SELV/PELV/NEC® Class 2 wiring connects keypads to other devices on the QS link. Each keypad counts as 1 device on the QS link. Each keypad column consumes 1 Power Draw Unit (PDU) on the QS link
ESD Protection	Meets IEC 801-2. Tested to withstand 15kV electrostatic discharge without damage or memory loss
Power Failure	Power failure memory: should power be interrupted, the keypad will return to its previous state when power is restored
Environment	Ambient operating temperature: 0°C / 32°F to 40°C / 104°F Relative humidity: 0% to 90% humidity, non condensing Application: Indoor use only
Regulatory Approvals	Lutron Quality Systems registered to ISO 9001:2015. Complies with UL 508; IEC 60669-2-1; and CSA C22.22 No. 14-13. EBB-1-3COL only – Complies with UL 2269; IEC 60670-1; and CSA C22.22 No. 18.2 (2006
Wiring	SELV/PELV/NEC® Class 2 Terminals: Each terminal accepts up to two 18 AWG (1.0 mm2) wires
Mounting	Typical square style wall box dimensions: Height: 75 mm / 2.95″ Width: 75mm / 2.95″ Depth: ≥25 mm / ≥0.98″ Typical round style wall box dimensions: 68 mm / 2.68″ Depth: ≥25 mm / ≥0.98″

The post LUTRON HWQS PALLADOM INTERNATIONAL 2 COLUMN KEYPAD, PRE ENGRAVED appeared first on Wave Electronics Systems.

LUTRON HOMEWORKS QS PALLADIOM INTERNATIONAL KEYPAD

admin — Fri, 23 Jun 2023 11:03:05 +0000

Lutron’s HWQS Palladiom International Keypad elevates the user’s experience with sleek and intuitive design and allows the control of Lutron load control devices via a QS link.

The keypad is pre engraved for extra convenience and is available in a variety of finishes.

Large tactile buttons are easy to use and button engraving is easy to read. Buttons and wall plates are made from the same material for a consistent aesthetic. Buttons with white, backlit engraving make it easy to find and operate the keypad in low light conditions. Status of active button press or scene is indicated through intensity of backlighting which is configurable through the HomeWorks QS software. Dynamic Backlighting Management (DBM) automatically adjusts backlight intensity based on ambient lighting conditions. It can also be programmed in the HomeWorks QS software to adjust intensity by time of day or button presses

Keypads are available in a variety of finishes.

FEATURES

Large buttons are easy to use
Buttons with white, backlit engraving make it easy to find and operate the keypad in low light conditions
Button engraving is easy to read
Status of active button press or scene is indicated through intensity of backlighting
Dynamic Backlighting Management (DBM) automatically adjusts backlighting intensity based on ambient lighting conditions
Available in a variety of colours and finishes
Faceplate snaps on with no visible means of attachment. Surface mount for easy installation, no backbox required
IP20 rated

SPECIFICATIONS

Power	24 to 36 VDC 30mA
Typical Power Consumption	0.7W Test conditions: All backlights on medium intensity, two LEDs on (two pre-sets active), keypad powered at 24VDC
Regulatory Approvals	Lutron Quality Systems registered to ISO 9001:2015. Complies with UL 508, IEC 60669-2-1and CSA C22.22 No. 14-13. EBB-1-3COL only Complies with UL 2269, IEC 60670-1 and CSA C22.22 No. 18.2 (2006
Environment	Ambient operating temperature: 0°C / 32°F to 40°C / 104°F Relative humidity: 0% to 90% humidity, non condensing Application: Indoor use only
Communications	SELV/PELV/NEC® Class 2 wiring connects keypads to other devices on the QS link. Each keypad counts as 1 device on the QS link. Each keypad column consumes 1 Power Draw Unit (PDU) on the QS link
ESD Protection	Meets IEC 801-2. Tested to withstand 15kV electrostatic discharge without damage or memory loss
Power Failure	Power failure memory: should power be interrupted, the keypad will return to its previous state when power is restored
Wiring	SELV/PELV/NEC® Class 2
Terminals	Each terminal accepts up to two 18 AWG (1.0 mm2) wires
Mounting	Typical square style wall box dimensions: Height: 75 mm / 2.95″ Width: 75mm / 2.95″ Depth: ≥25 mm / ≥0.98″ Typical round style wall box dimensions: 68 mm / 2.68″ Depth: ≥25 mm / ≥0.98″

The post LUTRON HOMEWORKS QS PALLADIOM INTERNATIONAL KEYPAD appeared first on Wave Electronics Systems.

HOMEWORKS WIRED ALISSE KEYPAD BASE UNIT

admin — Fri, 23 Jun 2023 11:03:05 +0000

The HomeWorks wired Alisse keypad allows the user to control lights, shades, draperies, temperatures and third party equipment. These keypads are available in a variety of colours and finishes, with optional text or icon engraving

The HomeWorks wired Alisse keypad allows the user to control lights, shades, draperies, temperatures and third party equipment.

The keypad is designed to work with Lutron HomeWorks QSX series processors only through the wired QS link.

Backlit buttons make it easy to find and operate the keypad in low light conditions.

Keypads are available in a variety of colours and finishes, with optional text or icon engraving.

Status of active button press or scene is indicated through intensity of backlighting which is configurable through the HomeWorks software. It can also be programmed in the HomeWorks software to adjust intensity by time of day or button presses.

The Alisse base unit is designed to allow system installation without exposing the keypad to potential damage during construction. It features a single programmable pushbutton for wiring validation and basic system control.

FEATURES

Supplied with Construction Cover
Base unit contains two non isolated contact closure inputs (CCIs) for integration with a contact closure device
The CCI can be set up to simulate existing Lutron keypad functionality or it can be custom configured to meet project specific requirements

SPECIFICATIONS

Power	24 to 36 VDC 30mA per base unit
Typical Power Consumption	Single column keypad + base = 370mW at 24 VDC Two column keypad + base = 449mW at 24 VDC Three column keypad + base = 543mW at 24 VDC
Regulatory Approvals	Lutron Quality Systems registered to ISO 9001:2015. cULus, CE, NOM, FCC, ICES-003 and RoHS compliant
Environment	Ambient operating temperature: 0 °C / 32 °F to 40 °C / 104 °F 0% to 90% non condensing relative humidity Indoor use only
Communications	SELV / PELV / NEC® Class 2 wiring connects keypads to other devices on the QS link. Each base unit counts as 1 device on the QS link. Each base unit consumes 1 Power Draw Unit (PDU) on the QS link. For complete information, see “Power Draw Units on the QS link” (Lutron P/N 369405)
ADA Standard	Control operation complies with ADA standards for an accessible design
ESD Protection	Meets IEC 801-2. Tested to withstand 15kV electrostatic discharge without damage or memory loss
Power Failure	Power failure memory: Should power be interrupted, the keypad will return to its previous state when power is restored
Dimensions	Typical square style backbox dimensions: Height: 75mm / 3″ Width: 75mm / 3″ Depth: ≥ 35mm / ≥ 1.4″ Typical round style backbox dimensions: Width: 68mm / 2.7″ Depth: ≥35mm / ≥1.4″ See Mounting on page 13 of the data sheet for more details
Wiring	SELV / PELV / NEC® Class 2.
Terminals	Each terminal accepts up to two 18AWG (1.0mm2) wires

The post HOMEWORKS WIRED ALISSE KEYPAD BASE UNIT appeared first on Wave Electronics Systems.

LUTRON HW QS PALLADIOM THERMOSTAT

admin — Fri, 23 Jun 2023 11:03:05 +0000

Lutron’s HomeWorks QS Palladiom Thermostat offers a convenient and aesthetically pleasing control of temperature and for intuitive heating and cooling adjustments. Available in a variety of finishes coordenated with Lutron’s Palladiom Keypads.

Temperature can be added to HomeWorks QS whole home scenes via keypad buttons, timeclocks or the Lutron Connect App, which gives your clients the ability to monitor and adjust temperature while home or away.

The Palladiom Thermostate works with most residential HVAC systems. Gas, oil, or electric Furnace, Air conditioning, Fan Coil Units, Heat Pumps, and underfloor heating systems. Please consulte the product specification document for more details.

FEATURES

Aesthetically coordinates with Palladiom keypads
Available in a variety of colour finishes finishes. Please see the Technical Specification section for further details
Backlit screen and buttons that include Dynamic Backlight Management (DBM) to automatically adjust backlight intensity based on ambient lighting conditions
Ability to support separate heating and cooling equipment on one thermostat
Displays temperature in Fahrenheit °F or Celsius °C
Palladiom thermostat continues operation if communication with the HomeWorks QS system is interrupted
Uses Lutron QS link for power and communication with other QS devices
Ships with a sealed wallbox for use in new or existing constructions, specifically for hollow walls that may have air movement in the wall cavity
IEC SELV/NECR Class 2 for 24VDC – 36VDC
IEC, CE, RoHS, cULus, and NOM compliant

SPECIFICATIONS

Regulatory Approvals	IEC, CE, cULus, RoHS, and NOM compliant
Operating Voltage	24VDC – 36VDC IEC SELV/ NECR Class 2 Power provided by QS link power supply
Typical Power Consumption	10mA at 24VDC
Maximum Power Consumption	60mA at 24VDC Test conditions: Backlight on full 3 Power Draw Units (PDUs)
Environment	Ambient operating temperature: 0°C to 40°C / (32°F to 104°F) Relative humidity: 5% to 90% humidity, non condensing Application: Indoor use only IP20 rating
Communications	Thermostat communicates with the HomeWorks QS system via 4 wire QS link protocol. It also communicates with the HomeWorks QS Palladiom HVAC controller and VRV/VRF interfaces via 3 wire HomeWorks QS Palladiom HVAC controller link
Room Temperature Sensor	Temperature display range: 0°C to 37°C (32°F/ 99°F) Temperature setpoint range: 10°C to 32°C (50°F/ 90°F) (programmable) Accuracy: At 25 °C: < +/− 0.5 °C At 70 °F: < +/− 1 °F
Power Failure	Should power be interrupted, the thermostat will retain all settings when restored power is restored
Mounting	Mount on a clean, dry, interior wall approximately 1.2m – 1.5m / 4 ft to 5 ft above the floor, please see the “Mounting” Section of the product data sheet for further details.
Wiring	IEC SELV/NEC Class 2: 24VDC –36VDC 22 AWG (0.5mm²) and 18 AWG (0.75 mm²) solid wiring
Dimensions	Height: 94mm / 3.7″ Width: 102mm / 4″ Depth: 25mm / 1″

The post LUTRON HW QS PALLADIOM THERMOSTAT appeared first on Wave Electronics Systems.

LUTRON HOMEWORKS QSX PROCESSOR 1 LINK

admin — Fri, 23 Jun 2023 11:03:05 +0000

The HomeWorks QSX processor provides control and communication to HomeWorks system components.

The HomeWorks QSX processor provides control and communication to HomeWorks system components. The Ethernet links allow communication to the HomeWorks designer software, integration with third party systems and communication between multiple processors.

HomeWorks QSX processors may be connected using either an Ethernet hub /switch or router, or by using Ethernet directly from a PC to the processors.

Clear Connect – Type X Gateways cannot be wired directly to the Ethernet port on a HomeWorks QSX processor.

All processors on a project must be connected to a single network.

The HomeWorks designer software and all integration equipment must be connected to the same network as the processors.

This processor is required when using the Clear Connect Type X Gateway for control of residential Ketra light sources.

The processor is powered from the QSPS-DH-1-75-H power supply. This processor can be installed in a HQ-LV21, L-LV21, L-LV14, or PDx control panel

FEATURES

Provides control and communication to HomeWorks system components
The Ethernet links allow communication to the HomeWorks designer software, integration with third party systems and communication between multiple processors
QSX processors may be connected using either an Ethernet hub /switch or router, or by using Ethernet directly from a PC to the processors

SPECIFICATIONS

Power	Processor (P): 24–36 V – 250 mA Links (L1 / L2): 24–36 V – 2 A per link
Typical Power	4.2 W; 8 Power Draw Units (PDUs)
Consumption	Test conditions: Two Ethernet links connected, both device links in use
Regulatory Approvals	cULus, NOM, CE
Environment	Indoor use only. 0°C / 32 °F to 40°C / 104°F 0% to 90% humidity, non condensing
Heat Generated	15 BTU/hr typical (24 BTU/hr with 2 links at 2 A each output)
Cooling Method	Passive cooling
Power Failure Memory	System data stored in non volatile memory Timeclock retention for 10 years
Internal Timeclock	±1 minute per year
Mis-wire Protection	All terminal block inputs are over-voltage and mis-wire protected against wire reversals and shorts
Low Voltage Link Wire Type	Two pair One pair 18 AWG (0.75mm 2), one pair 18 to 22 AWG (0.34 to 0.75mm 2) twisted shielded — IEC PELV / NEC® Class 2 cable
Low Voltage Power Wire Type	18 AWG (0.75mm 2)
Communications	Ethernet, RS485 (QS, RF)
Link Capacities	HomeWorks QS Wired Device Link 99 devices/512 zones HomeWorks QS Wired Device (MDU models) 50 devices/50 zones HomeWorks Clear Connect – Type A Link 99 devices/100 zones
ESD Protection	Meets or exceeds the IEC 61000-4-2 standard
Surge Protection	Meets or exceeds ANSI/IEEE C62.41 standard
Mounting	Mounts in HQ-LV21, L-LV14, L-LV21, or PDx- control panel
Dimensions	With terminal blocks: 108mm / 4.25″ x 100mm / 3.94″ Without terminal blocks: 108mm / 4.25″ x 90mm / 3.54″
Connections	4 pin removable terminal blocks. 1 for HQP7-1, 2 for HQP7-2. One 4 pin removable terminal block* for Power Input Two RJ45 standard Ethernet connections *Each terminal will accept up to two 18 AWG (0.75 mm 2) wires.

The post LUTRON HOMEWORKS QSX PROCESSOR 1 LINK appeared first on Wave Electronics Systems.

LUTRON HOMEWORKS QSX PROCESSOR 2 LINKS

admin — Fri, 23 Jun 2023 11:03:05 +0000

The HomeWorks QSX processor from Lutron provides control and communication to HomeWorks system components. This processor provides expanded connectivity and reliability and also streamlines and improves the installation process.

The QSX Processor is also compatible with all existing HomeWorks wired QS and wireless RF devices and securely connects to third party products with the built in Connect Bridge technology. The Ethernet links allow communication to the HomeWorks designer software, integration with third party systems and communication between multiple processors

HomeWorks QSX processors may be connected using either an Ethernet hub / switch or router, or by using Ethernet directly from a PC to the processor(s) and the HomeWorks designer software and all integration equipment must be connected to the same network as the processors. The HomeWorks QSX processor is required when using the Clear Connect – Type X Gateway for control of residential Ketra light sources.

The processor is powered from the QSPS-DH-1-75-H power supply. Refer to the HomeWorks designer software to determine link power requirements. Please see the related items sections for further information

FEATURES

The HomeWorks QSX processor 1 provides control and communication to HomeWorks system components
Ethernet links allow communication to the HomeWorks designer software, integration with third party systems and communication between multiple processors
QSX processors may be connected using either an Ethernet hub /switch or router, or by using Ethernet directly from a PC to the processor(s)
The processor is powered from the QSPS-DH-1-75-H power supply. Please see the related items section for further information
Each QSX processor can be individually configured as one of two types: HomeWorks QS wired device link99 devices / 512 zones or HomeWorks Clear Connect – Type A 99 devices / 100 zones

SPECIFICATIONS

Model Number	HQP7-2
Power	Processor (P): 24–36 VDC 250 mA Links (L1 / L2): 24–36 VDC 2 A per link
Typical Power Consumption	4.2W 8 Power Draw Units (PDUs) Test conditions: Two Ethernet links connected, both device links in use
Regulatory Approvals	cULus,NOM, CE
Environment	Indoor use only. 0°C / 32°F to 40°C / 140°F 0% to 90% humidity, non condensing
Heat Generated	15 BTU/hr Typical (24 BTU/hr with 2 links at 2 A each output)
Cooling Method	Passive Cooling
Power Failure Memory	System data stored in non volatile memory. Timeclock retention for 10 years
Internal Timeclock	±1 minute per year
Mis Wire Protection	All terminal block inputs are over voltage and mis wire protected against wire reversals and shorts
Low-Voltage Link Wire Type	Two pair — one pair 18 AWG (0.75 mm 2), one pair 18 to 22 AWG (0.34 to 0.75 mm 2) twisted shielded — IEC PELV / NEC® Class 2 cable
Low-Voltage Power Wire Type	18 AWG (0.75 mm 2)
Communications	Ethernet, RS485 (QS, RF)
Link Capacities	HomeWorks QS Wired Device Link 99 devices/512 zones HomeWorks QS Wired Device (MDU models) 50 devices/50 zones HomeWorks Clear Connect – Type A Link 99 devices/100 zones
ESD Protection	Meets or exceeds the IEC 61000-4-2 standard
Surge Protection	Meets or exceeds ANSI/IEEE C62.41 standard
Mounting	Mounts in HQ-LV21, L-LV14, L-LV21, or PDx- control panel
Dimensions	With terminal blocks: 108mm / 4.25″ x 100mm / 3.94″ Without terminal blocks: 108mm / 4.25″ x 90mm / 3.54″
Connections	4 pin removable terminal blocks. 1 for HQP7-1, 2 for HQP7-2. One 4-pin removable terminal block* for Power Input. Two RJ45 standard Ethernet connections. *Each terminal will accept up to two 18 AWG (0.75 mm 2) wires.

The post LUTRON HOMEWORKS QSX PROCESSOR 2 LINKS appeared first on Wave Electronics Systems.

LUTRON HOMEWORKS® QS PROCESSOR

admin — Fri, 23 Jun 2023 11:03:04 +0000

The QS processor from Lutron provides control and communication to HomeWorks® system components. Available in 1 Link and 2 Link.

The QS processor from Lutron provides control and communication to HomeWorks® system components.

The ethernet links allow communication to the HomeWorks® QS software, integration with third party systems and communication between multiple processors.

HomeWorks® QS processors may be connected using either standard networking or using adhoc networking. All processors on a project must be connected to a single network. The HomeWorks® QS software and all integration equipment must be connected to the same network as the processors. The processor is powered from the QSPS-DH-1-75 or QSPS-DH-1-60 power supply. Refer to the HomeWorks® QS software to determine link power requirements.

The QS processor can be installed in a L-LV21 or L-LV14 enclosure.

FEATURES

The HomeWorks® QS processor provides control and communication to HomeWorks® QS system components
Ethernet link allows communication to the HomeWorks® QS software, integration with third party systems and communication between multiple processors
HomeWorks® QS processors may be connected using either standard networking or using adhoc networking
All processors on a project must be connected to a single network
The processor is powered from the QSPS-DH-1-75 power supply

Configurable links to one of four types:

HomeWorks® QS Power Panels 16 interfaces / 256 zones
HomeWorks® QS Wired Device Link 99 devices / 512 zones
HomeWorks® QS RF Link 99 devices / 100 zones
HomeWorks® H48 Wired Dimmers 4 interfaces / 192 zones

SPECIFICATIONS

Power	Processor (P): 24 to 36VDC 250mA Links (L1 / L2): 24 to 36VDC 2 A per link
Typical Power Consumption	5W; 8 Power Draw Units (PDUs) Test conditions: Ethernet link connected and device link in use
Regulatory Approvals	Complies with: UL508, CSA – C22.2 No.14, IEC / EN 60669, NOM
Environment	Indoor use only. 0°C / 32°F to 40°C / 104°F 0% to 90% humidity, non condensing
Heat Generated	17 BTU/hr typical (24 BTU/hr maximum)
Cooling Method	Passive cooling
Power Failure Memory	System data stored in non volatile memory. Timeclock retention for 10 years
Internal Timeclock	±1 minute per year
Mis-wire Protection	All terminal block inputs are over voltage and mis-wire protected against wire reversals and shorts
Low-Voltage Link Wire Type	Two pair: One pair 18 AWG (0.75mm2), one pair 18 to 22 AWG (0.34 to 0.75 mm2) twisted shielded. IEC PELV / NECR Class 2 cable
Low-Voltage Power Wire Type	18 AWG (0.75mm2)
Communications	Ethernet, RS485 (QS, RF, Power Panel)
Link Capacities	HomeWorks® QS Power Panel Link 16 interfaces / 256 zones HomeWorks® QS Wired Device Link 99 devices / 512 zones HomeWorks® QS RF Link 99 devices / 100 zones HomeWorks® H48 Wired Dimmers 4 interfaces / 192 zones
ESD Protection	Meets or exceeds the IEC 61000-4-2 standard
Surge Protection	Meets or exceeds ANSI/IEEE C62.41 standard
Mounting	Mounts in L-LV14 or L-LV21 enclosures
Dimensions	Height: 134mm / 5.26″ Width: 108mm / 4.27″ Depth: 26.9mm / 1.06″
Warranty	Lutron Limited Warranty

The post LUTRON HOMEWORKS® QS PROCESSOR appeared first on Wave Electronics Systems.

LUTRON HOMEWORKS SWITCHING POWER MODULE – 5A

admin — Fri, 23 Jun 2023 11:03:04 +0000

Lutron HomeWorks 5A Switching Power Module is a 4 zone power module designed to control switching lighting loads. It includes QS link for seamless connection to a HomeWorks QS system.

Lutron HomeWorks 5A Switching Power Module is a 4 zone power module designed to control switching lighting loads.

It includes QS link for seamless connection to a HomeWorks QS system.

The adaptive zero cross switching technology maximises relay life expectancy.

It is rated for motor loads of 1/2 HP.

LEDs on the module provide diagnostic information and the buttons on module provide override control.

FEATURES

Rated for lighting loads as defined by IEC/EN 60669 as well as INC, MLV, and ELV
LEDs on the module provide diagnostic information
Buttons on the module provide override control
Manual Override Contact Closure Input (CCI)
Programmable Contact Closure Output (CCO)
Power failure memory automatically returns the outputs to the levels they were set to prior to a power outage

SPECIFICATIONS

Power	220 to 240V 50/60Hz Single input feed 16 A maximum total input current Lightning strike protection meets ANSI/IEEE standard C62.41 and IEC 61000-4-5 Can withstand voltage surges of up to 6 000V~ and current surges of up to 3 000A. ESD protected above agency requirements per IEC 60669-2-1 For ungrounded delta feed applications, contact Lutron
Regulatory Approvals	IEC/EN 60669 Lutron® Quality Systems registered to ISO 9001.2008 CE marked
Environment	Relative humidity: less than 90% non-condensing For indoor use only.
Output Zone Ratings	Each zone is rated at 5 A for switching. Rated for resistive, inductive or capacitive lighting loads as defined by IEC/EN 60669. Air gap off per output. No minimum load per output. This module is designed to control loads with ratings as noted in the table below. Outputs cannot be used to control general-purpose receptacles. Please consult the output Zone Rating section of the product specification sheet for further details under specific conditions.
Programming and Compatibility Requirements	Setup and programming of the Switching Module is done through the HomeWorks QS programming software. HomeWorks QS software version 12.0 or higher required.
QS Link Limits	A QS link in a HomeWorks QS system can have up to 512 zones (outputs) and 100 devices (required HomeWorks QS processor counts as 1 device on the QS link). Each Switching Module counts as one device toward the 100 device limit, and 4 zones toward the 512 zone limit.
Terminals	Torque – 0.6Nm (5in-lbs) Power terminals 1mm2 to 2.5mm2 (18AWG to 12 AWG) single wire, solid or stranded Data terminal 0.5mm2 to 2.5mm2 (22AWG to 12 AWG) single wire, solid or stranded 0.5mm2 to 1mm2 (20AWG to 18 AWG) two wires, solid or stranded
Mounting	Please consult the product specification sheet for mounting details.
Dimension	Height: 90mm / 3.54″ Width: 162mm / 6.38″ Depth: 61mm / 2.40″

The post LUTRON HOMEWORKS SWITCHING POWER MODULE – 5A appeared first on Wave Electronics Systems.

LUTRON HOMEWORKS SWITCHING POWER MODULE – 10A

admin — Fri, 23 Jun 2023 11:03:04 +0000

Lutron HomeWorks 10A Switching Power Module is a 4 zone power module designed to control switching lighting loads. It includes QS link for seamless connection to a HomeWorks QS system. Power Module units can be used in a HomeWorks QS system to control and manage light in an entire home or building.

Lutron HomeWorks 10A Switching Power Module is a 4 zone power module designed to control switching lighting loads.

It includes QS link for seamless connection to a HomeWorks QS system.

Power Module units can be used in a HomeWorks QS system to control and manage light in an entire home or building.

Rated for lighting loads as defined by IEC/EN 60669 as well as INC, MLV, and ELV.

LEDs on the module provide diagnostic information and buttons on the module provide override control.

FEATURES

Rated for lighting loads as defined by IEC/EN 60669 as well as INC, MLV, and ELV
LEDs on the module provide diagnostic information
Buttons on the module provide override control
Manual Override Contact Closure Input (CCI)
Programmable Contact Closure Output (CCO)
Power failure memory automatically returns the outputs to the levels they were set to prior to a power outage

SPECIFICATIONS

Power	230V~ 50/60Hz Lightning strike protection meets ANSI/IEEE standard 62.31-1980 Can withstand voltage surges of up to 6000V~ and current surges of up to 3000A Current draw: 50 mA max Standby power: 1 W BTUs/hour when fully loaded: 4
Regulatory Approvals	IEC/EN 60669-2-1, EN50428 Lutron® Quality Systems registered to ISO 9001.2008 CE marked C-Tick
Environment	Ambient Temperature Operating Range (inside mounting panel): 0 ºC to 40 ºC Calibration point maximum: 65 ºC Relative humidity: less than 90% non condensing For indoor use only.
Output Zone Ratings	Each zone is rated at 10 A for switching. Rated for resistive, inductive, or capacitive lighting loads as defined by IEC/EN 60669-2-1 Switched outputs utilise latching relays to maintain relay state if control power is lost.
Programming and Compatibility Requirements	Setup and programming of the Switching Module is done through the HomeWorks QS programming software. HomeWorks QS software version 3.0 or higher required.
QS Link Limits	A QS link in a HomeWorks QS system can have up to 512 zones (outputs) and 100 devices (required HomeWorks QS processor counts as 1 device on the QS link). Each Switching Module counts as one device toward the 100 device limit, and 4 zones toward the 512 zone limit.
Terminals	Torque – 0.6Nm (5in-lbs) Power terminals 0.5mm2 to 6mm2 Data terminal 0.5mm2 to 2.5mm2 (22AWG to 12 AWG) single wire, solid or stranded 0.5mm2 to 1mm2 (20AWG to 18 AWG) two wires, solid or stranded
Mounting	Please consult the product specification sheet for mounting details.
Dimension	Height: 90mm / 3.54″ Width: 162mm / 6.38″ Depth: 61mm / 2.40″

The post LUTRON HOMEWORKS SWITCHING POWER MODULE – 10A appeared first on Wave Electronics Systems.